Polymer Composite Maintenance Oil by Osmo

Osmo Polymer Composite Maintenance Oil is a Clear satin oil that penetrates the surface and will not build a film on the surface. Through impregnation, the surface becomes water repellent as well as resistant to dirt and stains.

Osmo Polymer Composite Maintenance Oil is suitable as a clear oil for maintaining and restoring weathered Wood Polymer Composites (WPC) and Bamboo Polymer Composites (BPC). Especially suitable for decking, privacy screens and garden furniture made of WPC or BPC.

Documents

Technical Data Sheet Safety Data Sheet

Directions for use

Surface Preparation:

The surface must be weathered, cleaned, dry and frost-free.
Osmo Polymer Composite Maintenance Oil is ready to use. Do not thin. Stir well.
Prior to application, the surface must be thoroughly cleaned with Osmo Polymer Composite Cleaner 8021. This ensures sufficient bonding.
Before applying Osmo Polymer Composite Maintenance Oil, rinse thoroughly with
water and allow to dry.

Application:

With Osmo Flat Brush or Osmo Decking Brush, apply very thinly and spread well.
Remove excess material (pooling or streaks) with a clean dry Osmo Decking Brush. Important: the liquid oil must be absorbed into the surface. There must not be any oil remaining on the surface or in grooves. Excess oil dries very slowly and produces a glossy oil layer without sufficient adhesion to the substrate.
Leave to dry for 8-10 hours. Ventilate well while drying.

Cleaning of tools:

With Osmo Brush Cleaner (free of aromatic compounds).

Drying time:

Approx. 8-10 hours (normal climatic conditions, 23 °C/50 % rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times.

Coverage:

1 litre covers approx. 40 m² with one coat. Product coverage depends significantly on the existing surface condition. All information refers to smooth surfaces. Other surfaces may lead to deviations in coverage.

Note:

Oils enhance the natural colour of the substrate (permanent wet effect). Trial application is required!
Impregnation may influence the slip resistance of the original surface. White or very light-coloured surfaces may become slightly yellow from oiling! Non-absorbent surfaces, such as glass, glazed tiles, ceramic or plastic, must be not treated (impregnated).

Caution:

Keep out of reach of children. Do not get in eyes, on skin, or on clothing. If medical advice is needed, have product container or label at hand. Use only outdoors or in a well-ventilated area. Warning: Wash out any used cloth impregnated with this product immediately after use or store in an airtight container (danger of self-ignition). Safety data sheet available on request.

Specifications

Classification	Oils & Oil Finishes for Wood
Brand	Osmo
Size	1 L
Sold Since	May 10, 2022
SKU	115 00 111
UPC	4006850089185
Composition	Based on natural plant oils (sunflower oil, soybean oil, thistle oil) , paraffin, siccatives (drying agents) and water repellent additives. Dearomatized white spirit (benzene-free). VOC classification in compliance with EU regulations (2004/42/EC): out of scope. Detailed declaration of ingredients available upon request
Drying Time	Approx. 8-10 hours (normal climatic conditions, 23 °C/50 % rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times.
Coverage	1 litre covers approx. 40 m² with one coat. Product coverage depends significantly on the existing surface condition. All information refers to smooth surfaces. Other surfaces may lead to deviations in coverage.
Odor	faint/mild, odourless after drying
Storage	5 years and longer if stored in the closed original can.
Tools cleaning	With Osmo Brush Cleaner (free of aromatic compounds)
Viscosity	30 - 50 mPas
Recommended Surfaces	Osmo Polymer Composite Maintenance Oil is suitable as a clear oil for maintaining and restoring weathered Wood Polymer Composites (WPC) and Bamboo Polymer Composites (BPC). Especially suitable for decking, privacy screens and garden furniture made of WPC or BPC.