EcoTrowel by EcoPoxy

In stock
from $11.95
Free shipping
on orders over $90
Quebec, Ontario · More info

EcoTrowel is a high performance epoxy filler and profiling product formulated for surface repair and preparation. It is easy to mix and spread, and has a peanut-butter like consistency (contains no peanuts !). EcoTrowel is lightweight and suitable for an infinite variety of composite, architectural, industrial and art-related applications. It can be applied to wood, concrete - even canvas - to a thickness of 1/2" without sagging or slumping. It can be easily sanded, shaped, drilled, tapped, machined, routered & remains durable for life.

EcoTrowel is easily mixed and spreads with a peanut butter like consistency with ease and control leaving a smooth cosmetic finish. Exhibits the ability to be molded or used on vertical and overhead surfaces without sagging and will not shrink when cured.

Suitable for interior and exterior art related use. EcoTrowel can be used to create textured or highly detailed display pieces. It can be stamped with a silicone rubber stam to crate repeating patterns with intricate detail over a large surface area. EcoTrowel is a very hard, heat resistant materiel that will readily accept paint and can also be colour pigmented.

  • 100% Solids, Low VOC's, Low Odor, Non Toxic
  • 100% Waterproof, Chemical Resistant, Impact Resistant and High Adhesion
  • Can be primed and coated
  • Superior strength and flexibility
  • Spreads easily and remains in place
  • Won't sag, drag or pull
  • No shrinking when cured
  • Use on flat, vertical or overhead surfaces

Directions for use

Preparation Instructions:

Remove all dust and loose debris from craks or surface using comressed air and/or a vacuum cleaner.

Mixing Instructions:

Squeeze part A and part B until the center pouch seal breaks. Then knead the contents of both parts together for 2-3 minutes, until color & texture are consistent throughout batch.

Application Instructions:

Using a trowel or putty knife, begin applying EcoPoxy Ecotrowel to prepped surface immediately after mixing.

Spread rate:

From a feathered edge up to 1.3 cm (0.5").

Working Temperature:

Surface should be 15-30°C (60-90°F)

*Note:

If 24 hours has elapsed from time of application, then additional preparation is required. To provide a profile for bonding, lightly sand entire surface with 120 grit sand paper until glossy finish has been removed. Remove all sanding dust and wipe down entire surface with isopropyl or denatured alcohol to remove contaminants.

Avoid contact with skin and eyes. In event of contact with eyes, rinse with water for 15 minutes and seek medical attention. In event of skin contact, rinse thoroughly with water. Do not ingest. If ingested, seek medical attention immediately. Do not induce vomiting.

Videos

Variants

25 g $11.95 In stock
100 g $23.95 In stock
Box (6 x 25 g) $59.95 In stock
Box (6 x 100 g) $119.95 In stock

Specifications

Category Epoxy
Brand EcoPoxy
Sizes
  • 25 g
  • 100 g
  • Box (6 x 25 g)
  • Box (6 x 100 g)
Sold Since May 6, 2018
Drying Time
  • Cure time: 48 hours @ 21°C (70°F) and 50% RH, using spread rate of 2.5m2/L ((100sf/gal).
  • Set to Touch: 6-8 hours
  • Recoat Time: 6-8 hours minimum
  • Foot Traffic: 24 hours

Depends on ambient temp, humidity and thickness.

Origin

Canada

Storage

10-25°C (50-77°F) Recommended.

Tools cleaning

Wipe tools and spills with a clean rag and Isopropyl/Denatured Alcohol or warm soapy water.

Recommended Surfaces

Concrete, Fiberglass, Masonry, Metal, Wood, ABS, PVC & More.

Pot Life

20 minutes (depending on ambient temp).

Similar products

Complementary products

Review

There is currently no review for this product. Be the first to submit one!

          

Terms of Sales · Privacy · En français