Bona Mega ONE - Waterborne Wood Floor Finish by Bona

New Product Professional Use

$119.95
Free Delivery
Quebec, Ontario · More info

Bona Mega ONE is an essential partner in the treatment of wooden floors. It is a crystal clear, quick-drying polyurethane varnish which offers excellent covering power. Bona Mega ONE® simplifies the craftsman’s everyday life, making the job faster and easier with the quality you depend on.

Bona Mega ONE is a clear, waterborne 1-component finish that dries fast, is easy to use and provides high build for superior protection. It brings out the beautiful, deep color of your wood while providing long-lasting protection for private interior floors and medium-traffic commercial spaces. Can be used with or without a primer. Bona Mega ONE offers a clear, non-yellowing formulation.

  • Full cure in 5 days
  • High build
  • Fast drying
  • Excellent abradability
  • Non-yellowing
  • GREENGUARD certified

Directions for Use

SURFACE PREPARATION

  1. Sand and prepare floor using accepted industry association methods.
  2. For a stained floor, make your final cut with 80 to 100-grit paper, then multidisc with 80 to 120-grit paper. For an unstained floor, make your final cut with 80 to 120-grit paper, then multidisc with 120 to 150-grit paper. This burnishing will reduce the amount of grain raise.
  3. Use a Tampico Brush on a buffer and vacuum thoroughly.
  4. Tack with a dry Bona® Microfiber Cleaning Pad or cloth.
  5. Apply Bona Finishing system.

THE BONA MEGA FINISH SYSTEM

Apply a Bona sealer or Bona stain and 2 coats of Bona Mega ONE®. Follow label directions. Adding a third coat of Bona Mega ONE® is recommended in heavy-traffic commercial and residential areas.

RECOMMENDED APPLICATORS

NOTE: Use a clean applicator for sealer and a separate clean applicator for finish.

FINISHING

SHAKE WELL BEFORE USING. DO NOT THIN.

  1. Pour a 6˝- wide line of finish along the starting wall. Go with the grain of the wood.
  2. Using a pre-dampened Bona floor coater, draw the floor coater forward with the grain of the wood, moving the finish toward the opposite wall. To maintain a wet edge at all times, hold the floor coater at a snowplow angle.
  3. At the end of each run, turn the floor coater and pull it toward you through the puddle; then pad out the floor coater parallel to the wet edge.
  4. Feather out all turns. Do not push too hard or too fast to avoid drips flying off the floor coater.
  5. BE SURE YOU ARE USING THE RECOMMENDED COVERAGE OF 500- 600 SQ. FT. PER GALLON. DO NOT SPREAD TOO THIN.
  6. Allow the first coat to dry 2-3 hours. High humidity and/or low temperature conditions will extend the dry time (recommended conditions of 65-80˚F/40-60% relative humidity).
  7. For smoothest results, see INTERCOAT ABRASION. At a minimum between coats, vacuum, and tack thoroughly with a Bona Microfiber Cleaning Pad (dry or slightly dampened with water).

INTERCOAT ABRASION

It is not necessary to abrade between Bona waterborne sealer and finish coats unless more than 48 hours has passed since the previous coat was applied. For smoothest results, abrade between each coat as necessary, using a multidisc and Bona Diamond 180 to 240-grit abrasives with Bona Intermediate Pads. Thoroughly clean abraded floor using Bona PowerScrubber® OR vacuum and tack with Bona Microfiber Cleaning Pads (dry or slightly dampened with water). When using solvent-based sealers, ALWAYS abrade, vacuum and tack before finish coats

RECOATING

Be sure floor is free from wax, polish, and oily residues. If contaminants are present, use the full Bona Recoat System™ to ensure adhesion. Otherwise, follow the Bona Prep® process. Adhesion failure can occur if these recoating processes are not followed and the floor has not been tested for compatibility.

CURING

The curing process takes approximately 5 days (75% cured after 1 day, 100% after 5 days). The floor may be walked on after 24 hours but remains susceptible to scuffing or marring until completely cured. Do not replace area rugs until the floor has fully cured.

CLEAN-UP

Application tools should be thoroughly cleaned with water and stored in an airtight container. Dispose of any remaining product in accordance with local, state and federal regulations.

FLOOR CARE

Use only a dry Bona Microfiber Mop or cloth for cleaning during the first week. Put walk-off mats at all entrance doorways to keep out excessive dirt and grit. Sweep or vacuum daily and clean as needed with Bona® Hardwood Floor Cleaner. Use felt pads under
furniture legs and appliances.

Variants

3.79 L (1 gallon) · Extra matte
WT300918002
$119.95 In stock
3.79 L (1 gallon) · Satin
WT300618002
$119.95 In stock
3.79 L (1 gallon) · Semi-Gloss
WT300318002
$119.95 In stock

Specifications

Classification Wood Varnishes
Brand Bona
Size 3.79 L (1 gallon)
Sold Since October 19, 2021
Drying Time

2 to 3 hours between coats
75% Cure : 24 hours
100% Cure : 5 days

Coverage

500-600 square feet per gallon

VOCs

275 g/L

Odor

Low, non-offending odour

Aspect

Milky white liquid

Storage

1 year shelf life in unopened container. Nonflammable - Bona Mega ONE should be stored in a climate controlled environment.

KEEP FROM FREEZING. Do not store above 38 °C (100 °F).

Compatibility

Stain, sealer, and finish results may vary widely depending on the wood species, especially on oily and resinous exotic species.

ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE AND DESIRED RESULTS.

Luster

60°:

40-45% for semi-gloss;
20-25% for satin;
7-9% for extra matte.

Solids

32%

Recommended Surfaces

Heavy-traffic residential- kitchens, entryways, family rooms, homes with pets, children, and high foot traffic, Commercial- restaurants, offices, retail stores, Hospitals, schools and universities, and nursing homes

Similar Products

Complementary Products

Review

There is currently no review for this product. Be the first to submit one!

          

Terms of Sales · Privacy · En français