Finitec 3000 - Water based polyurethane finish by Finitec

from $35.95
Free Delivery
on orders over $90
Quebec, Ontario · More info

Finitec 3000 varnish is a water-based polyurethane varnish for floors and furniture that offers remarkable resistance to wooden floors and furniture throughout the house.

Finitec 3000 is very easy to work with the Finitec applicator or with a 10 mm (3/8" roller). Finitec 3000 varnish is self-sealing, dries quickly and can be applied in a single day It can be applied over an old oil-based or water-based varnish.

Ultra resistant for residential traffic, with a non yellowing formula.

  • Waterborne finish
  • Superior resistance
  • Non yellowing
  • Easy application

Directions for use

New or restored floor:

Appropriate for the majority of oil or water based stains. Be sure the stain is completely dry and follow manufacturer’s recommendations carefully. Application must be done at room temperature between 21 and 25 ºC (70 and 77 ºF) and at a relative humidity of 45%.

  1. Sand following the wood grain, smooth the surface with a 120 grit sandpaper (DO NOT use steel wool) and remove dust with a vacuum cleaner and dry towels.
  2. Proceed to an adherence, compatibility and color test by reproducing jobsite application conditions and methods.
  3. Apply 3 to 4 coats of Finitec 3000 with the following application method:
    A) Mix the finish with a clean stick in order to provide a homogeneous product, then shake the finish vigorously for 45 seconds.
    B) Let stand at least 10 minutes to allow bubbles to break.
    C) Pour a finish line of 4 inches (10 cm) on floor along the wall and following the floor planks direction.
    D) Use a clean Finitec finish applicator, soak and apply the finish following the floor planks direction with a “snowplow” angle to always bring the excess liquid towards the untreated section. Overlap 4 inches (10 cm) the finished section. To prevent marks on the finish, DO NOT apply pressure on the applicator and smooth out marks and lines progressively. Be sure that coats are not too thin.
    E) Allow about 2 to 3 hours of drying between coats (may vary according to conditions).
    F) Sand between coats using a 180 grit sandpaper.
    G) It is not necessary to sand before the last coat if the time between the last two applications does not exceed 3 hours.
  4. Clean tools with water.

Recoating:

Appropriate for the majority of oil or water based finishes. Application must be done at room temperature between 21 and 25 ºC (70 and 77 ºF) and at a relative humidity of 45%.

  1. Clean thoroughly with Finitec Surface Preparation in order to eliminate accumulated dirt and to make the surface free of greasy residues.
  2. Sand evenly with the wood grain using a 120 grit sandpaper (DO NOT use steel wool). It is important to remove completely all shine on the floor (top coat). Remove dust with a vacuum cleaner and slightly damp towels. A more aggressive sanding is needed to restore prefinished floors.
  3. Proceed to an adherence, compatibility and color test by reproducing jobsite application conditions and methods. In case of incompatibility, sand completely to bare wood.
  4. Apply 1 or 2 coats of Finitec 3000 following the previous instructions A), B), C), D) and G).
  5. Clean tools with water.

N. B. Do not alternate with another product.

Warranty:

Finitec Hardwood Products Inc. certifies that the product is free from manufacturing defect. The user assumes all responsability for use in accordance with instructions of this label. Manufacturer’s responsibility is limited to the replacement of the product.

In case of eye or skin contact, rinse well with water for 15 minutes. In case of inhalation, allow the victim to rest in a well-ventilated area. If swallowed, seek medical attention. Do not induce vomiting. Have conscious person drink several glasses of water. KEEP OUT OF REACH OF CHILDREN.

Variants

1 L · Gloss
80200
$35.95 In stock
1 L · Satin
80220
$35.95 In stock
1 L · Semi-gloss
80210
$35.95 In stock
3.64 L · Gloss
81403
$119.95 In stock
3.64 L · Satin
81603
$119.95 In stock
3.64 L · Semi-gloss
81409
$119.95 In stock

Specifications

Classification Wood Varnishes
Brand Finitec
Sizes
  • 1 L
  • 3.64 L
Sold Since July 6, 2022
Drying Time

To touch: 1 hour
To recoat: 2 to 3 hours
Light traffic: 4 hours
Furniture: 24 hours
Carpets and rugs: 10 days
Complete cure: 10 days

Coverage

165 sq. ft. (15.3 m²) / liter (depending on conditions)

VOCs

275 g/L

Aspect

White Liquid

Storage

Store between 10 and 30 C (50 and 85 F) and keep from freezing.

Shelf Life

12 months, when kept in its original container

Tools cleaning

Water

Luster

Luster 60°:

Gloss : 90%
Semi-Gloss: 65%
Satin : 35%

Tools

Finitec applicator, T-bar, brush, spray gun or 3/8" (10 mm) roller

Viscosity

23 to 25 seconds (Zahn #2)

Solids

30% ± 2%

Similar Products

Complementary Products

Review

There is currently no review for this product. Be the first to submit one!

          

Terms of Sales · Privacy · Cookies · En français